Industrial IoT Digital Input Module

The LP-M01 Module is an encrypted wireless “LoRa” IO module with 4 dry contact digital inputs and 4 wet contact digital inputs(10-250VDC). The 3 wet contact inputs support Counter Inputs. It can communicate with LP-C01 receiver for Modbus input/output. The LP-C01 wirelessly controls LP-M01 modules via Modbus TCP or Modbus RTU for any SCADA or Control System client. Each LP-C01 will support up to 128 LP-M01 Modules.

Product Details

Features and Benefits

Flexible Monitoring Application

Without the need for new cables, digging trenches, oradding conduit. The encrypted communications provide a secure and reliable communication.

High Dependability

Debounce support in both software and hardware. Communications monitoring will alarm for low battery, interrupted communication, or any device malfunction. Rugged case suitable for tough environments.

Easy Integration

The LP-M03 and LP-C01 work together using the Modbus TCP/RTU protocol to extend the monitoring and control capabilities of remote l/O for PLC /Automation controllers.

Improved Safety & Data Transfer Reliability

Secured and encrypted wireless communications. Replace control wiring to outside cabinets with wireless antenna, eliminating unnecessary outages or the need to gothrough existing paths with dangerous voltage levels.

Savings on Capital Cost Investments

Reduce project costs and time using wireless communication instead of traditional wired applications. No trench, conduit, or raceway requirements, less laborfor design, documentation, installation, testing andmaintenance.

Transfer Switch System

Create a wireless version of pilot signals for any remote monitoring and control. The transfer switch system at M01+ reads an input and with the M03 module it quickly asserts the designated output to emulate, mirror, or momentary pulse.

LoRa Wireless Transmission Mode

The LP-C01 wirelessly controls LP-M01 modules via Modbus TCP or Modbus RTU for any SCADA or Control System client. Each LP-C01 will support up to 128 LP-M01 Modules.

Remote Synchronous Switch Modes

The LP-M01+ and LP-M02 are versatile input and output modules that communicate using the 915Mhz frequency
band radio spectrum. LP-M01+ and LP-M02 can be configured as remote synchronous switch modes, enabling
a hardwired switch input and remote synchronous switch output.An LP-M01+ input supports two operational
modes: P2P (point-to-point) with a single LP-M02 for output synchronization, and also P2MP (point-to-multipoint)
from one LP-M01+ to multiple LP-M02 outputs..

LP-M01 IO Function

The LP-M01 Module is an encrypted wireless “LoRa” IO module with 8 Total Binary Inputs, 4 internal wetted inputs for dry contacts and 4 inputs for any wetted contacts (10-250 VDC),Among these, 3 out of the 4 wet contacts can be configured as pulse input counters.  It can communicate with LP-C01 receiver for Modbus input/output.

Application

Power Supply:
12/24 V
10-30VDC, 3 Watts maximum

48/125V
36-200Vdc or 85-140 Vac 3 Watts maximum

125/250 V
85–300 Vdc or 85–264 Vac, 3 Watts maximum

Battery supply mode:
12VDC low power mode
3-year maximum battery life supported

Communications Interface:
Input latency:<100ms
Wireless communication encryption: AES128 with customized authorization key support.
Output Protocol: MODBUS TCP & MODBUS RTU

Wireless Frequency:915MHZ
Antenna: External
Channel: Single

Port: USB-C (setting port & firmware update)

Maximum wireless communication range:
1 mile

Digital Input Ratings:
Internal Wetted Voltage:
12VDC
Input Voltage Range: (add details for input voltage/AC input)
9-300VDC (the input voltage will be set per project requirement)

Operating Temperature:
–20°C to +65°C (–4°F to +149°F)

Dimensions:
6.05″L*4.5″W*2.4″H
154.59(mm)L*83.7(mm)W* 60.96(mm)H

Weight:
405g

Product Specifications
LP-M01 datasheet
LP-M01 Register Address Table
Product User Manual
LP-M01 User_Manual
Equipment Docking Guidance
LP-C01 Device Docking Documentation
Docking equipment video
Configuration Software
Configuration Software
LP-M01 Configuration Software UserManual
USB to 485 Driver